Description

The Genie Motion Control Time Lapse Device from Syrp is your key to the creative world of time lapse photography or real time video. The 4" cube takes up very little space in your bag and at only 3.3 lb it's easy to make it part of your standard rig. Linear and Panning Motion

Timer or Sensor Input

Preview Function

Custom User and Factory Pre-Sets

Bubble Level with Light

44 lb Load Capacity

12 Hour Battery

Multi-voltage Charger

Wide Camera Compatibility

Free Firmware Upgrade

The Genie, which allows both panning and linear motion control, attaches to standard gear such as dollies, sliders, jib arms and tripods. Simply attach the panning accessory to your tripod or support and mount your optional camera and ball head to the 3/8"-16 stud atop the Genie. The weight of your equipment is rarely a concern since it supports up to 44 lb. An illuminated bubble level is built in to help in setting up for panoramas. The Genie has factory presets such as Stars, People or Clouds but you can enter an unlimited amount of user presets into the Genie's memory for custom work. At maximum panning speed a 360ø pan takes 5 seconds, while 39" of linear movement takes 23 seconds.

Linear time lapse can be done on a rail or on a linear support system of your own making. While the Genie comes with 9.85' of rope to pull it across the rail, the movement of your time lapse is only limited by the length of your rope. Kevlar-cored rope with lengths of 328', 164' or 32.8' are available for separate purchase. The Genie has been tested successfully on a homemade 60' dual cable stretched over a lake.

Inputs include both USB for firmware and a sensor input. The free firmware upgrade enables bulb ramp-in and ramp-out functions and HDR (High Dynamic Range). Ramping is the process of modifying exposure settings on a camera in order to maintain a desired exposure value while the camera is in Bulb mode. This is especially valuable for transitional day into night, or night into day time lapses.

The sensor input accepts a motion, light, sound or other type of sensor to start your program in response to specific stimuli. The Genie ships with both panning and sliding bases, two slider mounts, 9.85' of rope and a multi-voltage charger for its built-in battery. A three-hour charge gives you about 12 hours of run time, depend on the weight of your camera. The Genie is compatible with approximately 130 cameras from nine major brands.

Dual Motion Panning and linear motion control with one device Versatile Attaches to any existing film equipment i.e. Dolly, Slider, Jib Arm etc. Sensor Input Auto start function through a timer or sensor or both. Sensor input allows for attachment of a motion sensor, light sensor, sound sensor and more Preview Preview function allows for revision of recording movement prior to recording Pre-Sets Factory pre-sets allow for instant shooting straight out of the box or storable user-programmable panning and tracking pre-sets Auto Start and Power Saving Auto Start enables the user to program camera movements to return to "home" and repeat again or continuously run the same movement. It also enables the user to setup time-lapse or camera movement to start on a delay timer. Auto Power Off shuts down the Genie when it's unused for 1 hour to save battery power Leveling Bubble level with light Ramping Firmware Bulb ramping is the process of modifying exposure settings on a camera in order to maintain a desired exposure value while the camera is in Bulb mode. A free firmware upgrade allows ramp-in, ramp-out function and HDR. Compatibility If your camera is not listed below, please contact Syrp to check compatibility.

Canon

7D, 70D, 60D, 50D, 40D, 30D, 5D, 20D, 10D, 5D Mark III, 5D Mark II, 1D X, 1D C, 1D Mark IV

1D (s) Mark III, 1D (s) Mark II (N), 1100D(T3), 1000D (XS), 100D (SL1), 700D (T5i), 650D (T4i)

600D (T3i), 550D (T2i), 500D (T1i),450D (XSi), 400D (XTi), 350D (XT), 300D, 300V, 3